Which chemistry for "HOLOFILM 250 PAR" from Applied Holographics PLC ?
Re: Which chemistry for "HOLOFILM 250 PAR" from Applied Holographics PLC ?
Excellent, Ed! Thank you!
Re: Which chemistry for "HOLOFILM 250 PAR" from Applied Holographics PLC ?
Very nice compilation, I printed several documents ![Smile :)](./images/smilies/icon_e_smile.gif)
I upgraded my 1mw Uniphase 1508P-0 by a 10mw hene tube with power source.
I gave it a few shots on this Holofilm. Result is still clearly not as nice as what I can get out of Ultimate plates from Mr Gentet, but it helps setting up my lab & I feel no gulty when messing up with this low-cost material.
@Ed were you ever able to achieve any "looking nice" Hologram on this Holofilm ? It's very dim for me, maybe because it really requires a pulsed ruby..
![Smile :)](./images/smilies/icon_e_smile.gif)
I upgraded my 1mw Uniphase 1508P-0 by a 10mw hene tube with power source.
I gave it a few shots on this Holofilm. Result is still clearly not as nice as what I can get out of Ultimate plates from Mr Gentet, but it helps setting up my lab & I feel no gulty when messing up with this low-cost material.
@Ed were you ever able to achieve any "looking nice" Hologram on this Holofilm ? It's very dim for me, maybe because it really requires a pulsed ruby..
Re: Which chemistry for "HOLOFILM 250 PAR" from Applied Holographics PLC ?
The holos of the waffle iron were pretty much what you would want, see the pictures earlier in the thread. Whether or not the magic came from the pulsed laser, not sure, as I haven't tested the film in single beam reflection mode with a CW laser.
But I did shoot a transmission holo with it, and thought it was pretty good, but I am traveling at the moment so I don't have a chance to take a picture of the comparison of the Holofilm 250 vs. Agfa 8E75HD.
Have you done an exposure series on the film? That will tell you everything. Keep going to higher levels of exposure until the image disappears, which tells you that have reached the saturation point and all the and all the developed silver has been removed in the dichromate reversal bleach. The image color will become greener before it disappears.
Hope this helps!
But I did shoot a transmission holo with it, and thought it was pretty good, but I am traveling at the moment so I don't have a chance to take a picture of the comparison of the Holofilm 250 vs. Agfa 8E75HD.
Have you done an exposure series on the film? That will tell you everything. Keep going to higher levels of exposure until the image disappears, which tells you that have reached the saturation point and all the and all the developed silver has been removed in the dichromate reversal bleach. The image color will become greener before it disappears.
Hope this helps!
"We're the flowers in the dustbin" Sex Pistols
Re: Which chemistry for "HOLOFILM 250 PAR" from Applied Holographics PLC ?
Thing is the longer exposure time, the higher the chances of a slight movement of the plate/object, whenever I try to go farther than approx 15 seconds I seem to loose the image completely on a "random" basis, like, sometimes I have a picture at 16 seconds sometimes not.
I have to improve again my stability if I want to go farther than 15 secs of exposure. Of course with your pulsed laser stability is no trouble xD
I'll make an exposure serie with the subject "touching" the film to make sure to focus on image contrast, I think the best I could achieve with this combination of laser/film was 1.5cm deep scene before it disapears in the black fog.
I have to improve again my stability if I want to go farther than 15 secs of exposure. Of course with your pulsed laser stability is no trouble xD
I'll make an exposure serie with the subject "touching" the film to make sure to focus on image contrast, I think the best I could achieve with this combination of laser/film was 1.5cm deep scene before it disapears in the black fog.
Re: Which chemistry for "HOLOFILM 250 PAR" from Applied Holographics PLC ?
Hey !
I just realized an obvious and cruel truth.
I won't be able to record satisfying holograms on this HOLO 250 PAR film with my HeNe laser !
The Holo film is designed to be sensitive in the very narrow area of 694nm (meant to be used with pulsed ruby) where my HeNe is most likely around 632nm :
This also explains why the exposure with a laser LED works better, the led must be some "InGaAlP" diode which emits somewhere between 630-685, probably in my case nearer to 685.
When reading the wonderful document shared by Ed here : http://edweslystudio.com/Materials/AgX/ ... 150186.pdf I can read that by this time Illford preconised to chemically process the "master holograms" which were recorded in 632 so that they would be shifted toward 694 for easier copy. (the holo 250 par film was used in holocopier).
So, as I don't intend to record a master transmission hologram (yet) then shift it 60nm up, i wonder if there would be any way to somehow shift sensitivity of the film closer to 630nm ? some undying maybe ? anyone heard of such thing ? I know we can pre-swell films somehow, would that help ?
I just realized an obvious and cruel truth.
I won't be able to record satisfying holograms on this HOLO 250 PAR film with my HeNe laser !
The Holo film is designed to be sensitive in the very narrow area of 694nm (meant to be used with pulsed ruby) where my HeNe is most likely around 632nm :
This also explains why the exposure with a laser LED works better, the led must be some "InGaAlP" diode which emits somewhere between 630-685, probably in my case nearer to 685.
When reading the wonderful document shared by Ed here : http://edweslystudio.com/Materials/AgX/ ... 150186.pdf I can read that by this time Illford preconised to chemically process the "master holograms" which were recorded in 632 so that they would be shifted toward 694 for easier copy. (the holo 250 par film was used in holocopier).
So, as I don't intend to record a master transmission hologram (yet) then shift it 60nm up, i wonder if there would be any way to somehow shift sensitivity of the film closer to 630nm ? some undying maybe ? anyone heard of such thing ? I know we can pre-swell films somehow, would that help ?